This feature is wonderful for creating your own cutwork needle designs, as it allows you to place a basting line at any point of the embroidery, not just at the beginning. Set the stitch length between 2.0mm and 8.0mm. Set the margin width and stitch length in Preferences. You can also set the distance from the embroidery, or margin width. What's great about this feature is that you can change the stitch length from the preset stitch length on your embroidery machine. If you place the automatic basting line around all stitches in a project with one design, you can use this to secure the fabric and stabilizer before beginning embroidery. Use this tool to insert a rectangular basting line automatically around the visible stitches. Modify window of the Control Panel in TruE™ Modify. Once exported as an embroidery design it can be inserted as many times as needed allowing you to make sureĮach section of the embroidery will line up with the previous one.Have you ever wanted to add a basting line around part or all of your embroidery? The Automatic Basting Line Around Visible Stitches tool is found on the Use TruE™ Create to produce a single alignment stitch embroidery design. You may want to add some additional stitches (Alignment stitches) to each section. If your design requires exact alignment when stitching it back together Selection tools to split the design into multiple embroideries, saving each section as a single embroidery design. Select the Paste function from the Design Menu to insert the design into your work area. Once the layout is finished, select Combine All from the Design Menu and then Copy the embroidery to the clipboard.Ĭhoose the desired hoop which is compatible with your embroidery machine. The example design was created in a 16" (400mm x 400mm) square hoop using the SuperDesignĮlements with Encore and Alignment tools. Start by creating a design in a hoop larger than any your embroidery machine may handle.
You can also use TruE™ Modify to manually split large designs into smaller hoops.
This allows you to move a design slightly when going from one hoopĪrea to another to align a turned hoop to stitch out the other side of the embroidery. Tolerance keeps the stitches a short distance from the edges of the overlap. Intelligent Split cuts through the minimum number of stitches and minimizes cuts Straight Line Split cuts the embroidery straight across the center line of the overlap zone. The hoop just place your embroideries in the most pleasing arrangement. There is no need to ensure each embroidery element is located in one or the other stitch area of Use the Intelligent or Straight Line Split settings depending on your preference. When you reopen the embroidery you will see it has been split automatically according to your Export settings. Įxport the finished embroidery file because it is now ready to sew. This example shows a design created using a variety of SuperDesign elements that have been perfectly spaced using theĮncore and Alignment functions available in TruE™ Studio. Start by creating your embroidery in a multipart hoop. Selected embroideries is adjusted equally.ĭid you know that the software splits your designs automatically for multipart hoops upon Export? Don't have a Multipart Hoop? Don't worry. You can distribute the embroideries vertically and or horizontally and the excess space between the In addition to lining things up the two additional functions will assist you for spacing. You can align embroideries using the top, bottom, left or right edges, center them vertically or horizontally. There are four Vertical Alignment and four Horizontal Alignment functions. This is great for creating embroideries which take advantage of the entire hoop area. Located outside the stitchable area of the hoop to just inside the edge. The Move into Hoop function allows you to move any selected embroideries The Center in Hoop function allows you to move the selected embroidery into the middle of the selected hoop. The Vertical and Horizontal Alignment functions do however require you to have multiple embroideries selected. Move into Hoop function with single or multiple embroideries. You can use the Center in Hoop icon with a single embroidery design and the ĭifferent functions are available at different times depending upon what is selected in the work area. The Control Panel in both TruE™ Studio and TruE™ Modify. The most commonly used alignment tool,Ĭenter in Hoop is also available from the Design Tab within Embroideries can be arranged using a variety of options including Center in Hoop, Move into Hoop as well as the various optionsįor both horizontal and vertical alignment.Īll of the alignment tools can be found under the Design menu within TruE™ Studio. Alignment tools allow you to arrange designs with precision.
0 kommentar(er)
